Numerical simulation of water and heat transport in the cathode channel of a PEM fuel cell

Cathode channel of a PEM fuel cell is the critical domain for the transport of water and heat. In this study, a mathematical model of water and heat transport in the cathode channel is established by considering two-phase flow of water and air as well as the phase change between water and vapor. The transport process of the species of air is governed by the convection-diffusion equation. The VOSET (coupled volume-of-fluid and level set method) method is used to track the interface between air and water, and the phase equilibrium method of water and vapor is employed to calculate the mass transfer rate on the two-phase interface. The present model is validated against the results in the literature, then applied to investigate the characteristics of two-phase flow and heat transfer in the cathode channel. The results indicate that in the inlet section, water droplets experience three evolution stages: the growing stage, the coalescence stage and the generation stage of dispersed water drops. However, in the middle and outlet sections of the channel, there are only two stages: the growth of water droplets, and the formation of a water film. The mass transfer rate of phase change in the inlet section of the channel varies over time, exhibiting an initial increase, a decrease followed, and a stabilization finally, with the maximum and stable values of 1.78 × 10^?4 kg/s and 1.52 × 10^?4 kg/s for Part 1, respectively. In the middle and outlet sections, the mass transfer rate increase firstly and then keeps stable gradually. Furthermore, regarding the distribution of the temperature and vapor mass fraction in the channel, near the upper surface of the channel, the temperature and vapor mass fraction first change slightly (x < 0.03 m) and then rapidly decrease with fluctuations (x > 0.03 m). In the middle of the channel, the temperature and vapor mass fraction slowly decrease with fluctuation.     

成型温度对PBX装药内部质量及性能的影响

针对压制成型的PBX炸药装药，选择CT无损检测、巴西实验和扫描电镜检测等技术，对比研究了室温和加热两种温度下压制成型的炸药装药内部质量、静态力学性能和细观破坏形式。结果表明，加热压制有利于改善炸药装药的内部质量，可避免产生初始损伤，且提高了装药的力学性能。细观尺度上，室温压制成型的装药主要发生界面脱黏破坏，加热压制成型装药的主要破坏形式是穿晶断裂。     

电气化铁路既有线深路堑扩堑石方控制爆破

介绍电气化铁路既有线无隔墙台阶爆破扩堑方法。沿既有线方向设置低台阶 ,边界处布置光爆孔 ,采用“同列同段和列间微差”的起爆网路。采用自制的“炮被”和架设“钢管排架”阻挡飞石、滚石和滑石 ,确保了既有线的安全。文中还概述了“炮被”和“钢管排架”的制做以及作者的认识和体会。     

角行程阀门电液执行器传动结构的分析

介绍了角行程电液执行器的几种常见传动结构,分析了各种结构的力矩输出特性及与阀门配套的特点。     

Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

Fabrication and laser performances of Yb:Sc2O3 transparent ceramics from different combination of vacuum sintering and hot isostatic pressing conditions

In this paper we report on the preparation and laser performance of transparent 3at.% Yb:Sc₂O₃ ceramics by reactive sintering of commercially available powders under vacuum followed by hot isostatic pressing (HIP). Combinations of different vacuum sintering temperatures (1650 °C and 1750 °C) and different HIP treatments (1700 °C and 1800 °C at 200 MPa) were tested in order to understand how these steps influence the microstructure and thus the optical and lasing properties of the ceramic samples. All the samples showed a good optical quality. The microstructure analysis and the laser tests showed that the vacuum pre-sintering temperature is the key factor determining the quality of the samples and the laser performances. The best values of slope efficiency i.e. η_L = 50 % and output power i.e. P_out = 6.62 W were obtained for the sample pre-sintered under vacuum at 1650 °C and hot isostatically pressed at 1800 °C.     

自然循环窄矩形通道内过冷沸腾两相摩擦阻力特性

采用去离子水作为实验工质，在低压低流速自然循环工况下开展了单面加热可视化窄矩形通道内的过冷沸腾摩擦阻力特性实验研究。实验中测量了实验段内的压降数据，并通过高速摄影仪拍摄了窄矩形通道内的气液两相图像，提出了过冷沸腾条件下的两相摩擦压降的剥离计算方法。基于本实验中获得摩擦压降数据，对分别基于均相流模型和分液相模型的经典两相摩擦压降计算关系式进行了评估，实验结果表明：采用不同等效黏度计算方法的均相流模型计算结果比实验值明显偏小；而分相流模型中，Sun and Mishiba关系式和Tran关系式均能够较好地预测摩擦阻力，计算值与实验值的平均相对偏差在±15%以内。结合实验数据，以分相流模型方法为基础，考虑全液相Reynolds数、Martinelli参数和Laplace数的影响，获得了计算分液相折算系数的经验关系式，与实验数据符合较好, 平均相对误差在10%范围内。     

关于硬件木马电路检测技术分析及发展趋势探讨

本文结合HTH电路的复杂性等特征分析与实际应用现状,研究了HTH电路的具体检测技术方法并对当前热点技术进行对比分析,探讨了HTH电路检测方法的技术发展趋势。     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.